Product details
The pen plating silver bath JE39 for pen is especially suitable for partial plating, for multi-colour processeing and reparation or restoration.
The deposited coatings have a bright and shiny silver colour.
The plating layer created by pen plating is very thin. If you would like a thicker layer, we recommend that you treat the goods in a normal electroplating bath. Jewellery parts that are not to be electroplated must then be covered with a suitable varnish.
Silver content: 2 g/100ml Ag
Voltage: 2-6 Volt
Bath temperature: room temperature
*** Plus 2 g silver at daily quotation***
Devices:
You will need a pen for plating (anode) with a replaceble felt as (+)- Pol and a tweezer/clamp (cathode) as (-)-Pol, each with a connecting cable as well as a rectifier (at least 10 V/2 Amp.).
Any available rectifier can be used.
Operating instructions:
Anodes: pen for plating and felt
Cathode surface: tweezer or clamp
Voltage: 2-6 Volt
Temperature: room temperature
Treatment time: few seconds
Goods movement: pen strokes
This product contains chemical substances that are subject to labelling requirements under REACH and CLP regulations.
Signal word: Danger
Hazard statements (H-statements)
H315 Causes skin irritation.
H318 Causes serious eye damage.
H411 Toxic to aquatic life with long lasting effects.
Precautionary statements (P-statements)
P264.1 Wash hands thoroughly after handling.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing.
P310 Immediately call a POISON CENTER or doctor.
P501.9 Dispose of contents/container as problematic waste.
The deposited coatings have a bright and shiny silver colour.
The plating layer created by pen plating is very thin. If you would like a thicker layer, we recommend that you treat the goods in a normal electroplating bath. Jewellery parts that are not to be electroplated must then be covered with a suitable varnish.
Silver content: 2 g/100ml Ag
Voltage: 2-6 Volt
Bath temperature: room temperature
*** Plus 2 g silver at daily quotation***
Devices:
You will need a pen for plating (anode) with a replaceble felt as (+)- Pol and a tweezer/clamp (cathode) as (-)-Pol, each with a connecting cable as well as a rectifier (at least 10 V/2 Amp.).
Any available rectifier can be used.
Operating instructions:
- The parts must be cleaned, rinsed well and dried before the pen plating procedure.
- Insert a felt tip into the handpiece (plus pol) and plug also into the pen plating unit
- Fix the part with a pair of tweezers (minus pol) and plug in the pen plating unit. Dip the felt tip into the pen plating
solution and wait 1 -2 minutes so that the solution can be adsorbed. Then insert the tip into the pen as far as possible - Stroke several times without applying pressure the area to be electroplated.
- Rinse well in fresh water and dry the part
Anodes: pen for plating and felt
Cathode surface: tweezer or clamp
Voltage: 2-6 Volt
Temperature: room temperature
Treatment time: few seconds
Goods movement: pen strokes
Notice according to REACH Regulation (EC) No. 1907/2006:
This product contains chemical substances that are subject to labelling requirements under REACH and CLP regulations.
Signal word: Danger
Hazard statements (H-statements)
H315 Causes skin irritation.
H318 Causes serious eye damage.
H411 Toxic to aquatic life with long lasting effects.
Precautionary statements (P-statements)
P264.1 Wash hands thoroughly after handling.
P273 Avoid release to the environment.
P280 Wear protective gloves/protective clothing/eye protection/face protection.
P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact
lenses, if present and easy to do. Continue rinsing.
P310 Immediately call a POISON CENTER or doctor.
P501.9 Dispose of contents/container as problematic waste.